Measuring Your Horse For A Bit

Methods of measurement

$T2eC16F,!zQE9s3sqIw0BRM7TC!Wy!~~60_35

There are various devices (mouth measures) available that will enable you to measure your horse’s mouth in order to determine the correct size of bit.  We’ll look at some examples below.

This design is bulky and it takes time to adjust. This method of measuring is invasive and although accurate when used correctly if the horse hasn’t been bitted previously it may not be the most practical.

Heather’s homemade mouth measure;

Photo of bit measure

This is a better alternative to simply using a piece of string. Position it within the mouth where the bit would sit with the rubber snug against one side, apply some tension and then measure the distance between the rubber disc and the fingertips positioned snug against the corner of the opposite lip.  This will then determine the size of a fixed cheek design.  Remember that for a loose ring design you need to add half an inch to this value.

The other common method of measuring is to use an existing bit which has been measured and then the fit is assessed in situ. Obviously this is only a good guide if the bit is a near fit anyway.

Problems due to poor fit

A poorly fitting bit is a common cause of mouth trauma.  Rubs in the corner of the mouth are possibly the most common form of such trauma and they

may be caused by using a bit that is too small but also by a bit that is too wide!  In the latter case the cause is friction as the bit slides back and forth as the rider asks for turns etc.

arubs1

You are probably the only person that has the opportunity to check your horse’s mouth on a regular basis.

It is important to look for anything unusual, including any signs of bruising, cuts, etc. Check out the tongue and don’t forget to look underneath as ulcers and trauma can occur here.  The tongue may be lifted gently in order to look underneath but do not grab it and hang on as it is a muscle and damage may occur. Check out the upper and lower palate and bars for any sign of rubbing. Don’t forget to look inside the cheeks in case the flesh has been pushed into the teeth by the cheek of the bit.  This is not an uncommon injury and is often only found by the dentist. Obviously if the external corners of the lips are rubbed it will be clearly apparent, but don’t forget to turn the corner out to check for rubbing inside.

Checking for the correct size with your bit in situ

A general guide to ensuring your bit is at the correct height in the mouth would be to aim for ½ – 1 lip wrinkles at the corners of the mouth.  Please bear in mind that mouth conformation varies and some horses are much shorter from the corner of the lip to the muzzle (‘short smile’).  In this case it is often tempting to shorten the cheek pieces excessively thus causing the horse much discomfort and to appear to grin like a Cheshire cat.

Eggbutt

When fitting a bit with a fixed cheek, such as the Eggbutt, the lip should gently brush up against the butt end ensuring a snug, although not tight, fit.

If using a very popular lozenge loose ring such as the Team Up then the general rule would be to have clearance either side of no more than one eighth of an inch from the corner of the lip up to the hole that the ring passes through.

Loose Ring

The fit of the bit needs to be assessed at rest and then with a contact. It is quite common for riders to employ loose rings that are too big.

Aspects of Neue Schule Design

Neue Schule bits are produced using state of the art design and manufacturing techniques. We work with Computer Aided Design and a mathematical formula is inbuilt so as we do not lose the integrity of the design with varying sizes. All of the mouthpieces use individual casting molds and the designs are available in quarter inch increments. This ensures that a correct fit is obtained to effectively employ the correct pressure points within the mouth thus maximising on comfort and communication.

How to Measure A Neue Schule Bit

In order to determine whether your current bit is the right size and positioned correctly within the mouth simply photograph the bit in situ and e-mail us.

For further information and advice please visit www.nsbits.com.

Our advice line is 08446644600 for individual bitting advice.

We also have a Youtube channel www.youtube.com/neueschulebits and a facebook page www.facebook.com/nsbits.

You can also email enquiry@nsbits.com.

Heather Hyde, Neue Schule

Recent Blog Posts

View All
11th October 2019

Fit to Ride

Researchers have found riding as a sole mode of exercise is not adequate to improve fitness. The rider needs to find time away from the horse to participate in a […]

Keep up to date

Sign up to the Neue Schule newsletter for the latest news, competitions and much more...


We use cookies. By browsing our site you agree to our use of cookies.Accept

If the spinner keeps loading forever, click to hide it.
Loading...